Electric Motor Repair Electric Motor Maintenance-Martindale Products
Española
Français
sales@martindaleco.com
phone:  216-521-8567
fax:       216-521-9476
Site Search:

CLICK HERE for Printable Version of this page.

Type MSL --- Metal Slitting Saws
Used for deep-slotting of Steel and Cast Iron --- also cast Brass and Aluminum and similar hard non-ferrous metals.  Has a stronger tooth and gives a better finish with less bur.
Metal Slitting Saw

M-2 High Speed Steel

Hollow Ground
For Side
Clearance

Ground Land

Rake Angle
of Teeth: 0°

Ground Teeth

Metric Sizes Available

Tolerances:
O.D. = ±.005
Thickness = ±.0005
I.D. = +.001 -.000
(Closer tolerances
available at
additional cost.)

NOTE:
     Saws in schedule are stocked for immediate shipment, Intermediate thickness, use next higher price in schedule (plus a slight grinding charge for smaller quantities).
     We'll gladly quote on other sizes, rake angles, tooth styles, hole sizes, etc. --- just send us your print or sample saw.
     Teeth can be alternately beveled if chips tend to stick in slot

RESHARPENING SERVICE
Complete resharpening
service is available.

COATING SERVICE
TiN, TiCN and other surface
coatings are available.

STOCK SAWS

Thickness

O.D.

2-1/2"

3"

4"

5"

6"



Fraction

Decimal

Hole

7/8"

1"

1"

1"

1"

No. of
Teeth

28

30

36

44

50

3/16"

.1875"

OMSLE1875 OMSLF1875 OMSLG1875

5/32"

.1562"

OMSLD1562

 OMSLE1562 OMSLF1562 OMSLG1562

1/8"

.1250"

OMSLH1250

OMSLD1250

 OMSLE1250 OMSLF1250 OMSLG1250

3/32"

.0937"

 OMSLH0937 OMSLD0937 OMSLE0937 OMSLF0937 OMSLG0937

1/16"

.0625"

 OMSLH0625 OMSLD0625 OMSLE0625 OMSLF0625 OMSLG0625

3/64"

.0468"

 OMSLH0468 OMSLD0468 OMSLE0468 OMSLF0468 OMSLG0468

1/32"

.0312"

 OMSLH0312 OMSLD0312 OMSLE0312
 

Ground Teeth

M-2 High Speed Steel

Hollow Ground For Side Clearance

Rake Angle of Teeth: 0°

Metric Sizes Available

Type SS Screw
Slotting Saws
Used for Cutting-off, slitting
and slotting of Steel
(Similar to slots in screw heads).

NOTE:
     Saws in schedule are stocked for immediate shipment.  For thicknesses not shown, use next higher price in schedule (plus a slight grinding charge for smaller quantities).
     Other diameters from 1/4" to 6" are also available, as well as other hole sizes, numbers of teeth, rake angles and bevels.
     Cutting Stainless Steel requires more side clearance - specify "for Stainless" when ordering.
Coating Service
TiN, TiCN and other coatings are available.  Prices on application.		 Resharpening Service
Complete Resharpening service is available. 
Prices on application.

Tolerances: O.D. ± .005; Thickness ± .001;
I.D. +.001 - .000
Closer tolerances available at additional cost.

STOCK SAWS
Thickness O.D. 1-3/4" 2-1/4" 2-3/4" 3" 4" 5" 6"
B & S Gage No. and Fraction Decimal Hole 5/8" 5/8" 1" * 1" 1" 1" 1"
No. of Teeth 64, 90 60 36, 44
56, 72		 36, 44
56, 72		 60, 72
90		 60, 72
90, 110		 72, 90
120
3/16" .187"       OSSC187 OSSD187 OSSE187 OSSF187 OSSG187
5 .182"       OSSC182 OSSD182 OSSE182 OSSF182 OSSG182
11/64" .172"       OSSC172 OSSD172 OSSE172 OSSF172 OSSG172
6 .162:       OSSC162 OSSD162 OSSE162 OSSF162 OSSG162
5/32" .156"       OSSC156 OSSD156 OSSE156 OSSF156 OSSG156
7 .144"       OSSC144 OSSD144 OSSE144 OSSF144 OSSG144
9/64" .141"       OSSC141 OSSD141 OSSE141 OSSF141 OSSG141
8 .128"       OSSC128 OSSD128 OSSE128 OSSF128 OSSG128
1/8" .125"     OSSB125 OSSC125 OSSD125 OSSE125 OSSF125 OSSG125
9 .114"     OSSB114 OSSC114 OSSD114 OSSE114 OSSF114 OSSG114
7/64" .109"     OSSB109 OSSC109 OSSD109 OSSE109 OSSF109 OSSG109
10 .102"     OSSB102 OSSC102 OSSD102 OSSE102 OSSF102 OSSG102
3/32" .094"     OSSB094 OSSC094 OSSD094 OSSE094 OSSF094 OSSG094
11 .091"     OSSB091 OSSC091 OSSD091 OSSE091 OSSF091 OSSG091
12 .081"     OSSB081 OSSC081 OSSD081 OSSE081 OSSF081 OSSG081
5/64" .078"     OSSB078 OSSC078 OSSD078 OSSE078 OSSF078 OSSG078
13 .072"   OSSA072 OSSB072 OSSC072 OSSD072 OSSE072 OSSF072 OSSG072
14 .064"   OSSA064 OSSB064 OSSC064 OSSD064 OSSE064 OSSF064 OSSG064
1/16" .062"   OSSA062 OSSB062 OSSC062 OSSD062 OSSE062 OSSF062 OSSG062
15 .057"   OSSA057 OSSB057 OSSC057 OSSD057 OSSE057 OSSF057 OSSG057
16 .051"   OSSA051 OSSB051 OSSC051 OSSD051 OSSE051 OSSF051 OSSG051
3/64" .047"   OSSA047 OSSB047 OSSC047 OSSD047 OSSE047 OSSF047 OSSG047
17 .045"   OSSA045 OSSB045 OSSC045 OSSD045 OSSE045 OSSF045 OSSG045
18 .040"   OSSA040 OSSB040 OSSC040 OSSD040 OSSE040 OSSF040 OSSG040
19 .036"   OSSA036 OSSB036 OSSC036 OSSD036 OSSE036    
20 .032"   OSSA032 OSSB032 OSSC032 OSSD032 OSSE032    
1/32" .031"   OSSA031 OSSB031 OSSC031 OSSD031 OSSE031    
21 .028"   OSSA028 OSSB028 OSSC028 OSSD028 OSSE028    
22 .025"   OSSA025 OSSB025 OSSC025 OSSD025 OSSE025    
23 .023"   OSSA023 OSSB023 OSSC023 OSSD023 OSSE023    
24 .020"   OSSA020 OSSB020 OSSC020 OSSD020 OSSE020    
(ADD NO. OF TEETH TO CATALOG NUMBER WHEN ORDERING)
* 3/4" hole available at no extra cost on 2-3/4" O.D. × 72-teeth. (Available at extra cost on all others.)

Type SMF - Copper Slitting Saws
Slitting Saw

Ground and Landed Teeth

 M-2 High Speed Steel

Hollow Ground
For Side
Clearance

Alternately Beveled Teeth

Rake Angle of Teeth: 10°
Positive

Metric Sizes Available

Used for cutting rolled Aluminum and Copper - materials that produce long stringy chips.

RESHARPENING SERVICE
Complete resharpening
service is available.
Prices on Application

COATING SERVICE
TiN, TiCN and other surface
coatings are available.
Prices on application
Tolerances: O.D. ± 0.005;
I.D. +0.001 - 0.000 Closer tolerances available at additional cost

Alternately beveled teeth
(see sketch) produce chips of less than the width of the slot being cut, eliminating the tendency of the chips to clog.

Note:
For prices of thickness not shown, use next higher price in schedule (plus a slight grinding charge for smaller quantities).  Other diameters, hole sizes, thickness, number of teeth, also available on application. 

Thickness O.D. 2-1/2" 3" 4" 5" 6"
Fraction Decimal Hole 7/8" 1" 1" 1" 1"
No. of Teeth 20 24 26 32 36
3/16" 0.1875"       OSMFE1875 OSMFF1875 OSMFG1875
5/32" 0.1526"     OSMFD1562 OSMFE1562 OSMFF1562 OSMFG1562
1/8" 0.1250"   OSMFH1250 OSMFD1250 OSMFE1250 OSMFF1250 OSMFG1250
3/32" 0.0937"   OSMFH0937 OSMFD0937 OSMFE0937 OSMFF0937 OSMFG0937
1/16" 0.0625"   OSMFH0625 OSMFD0625 OSMFE0625 OSMFF0625 OSMFG0625
3/64" 0.0468"   OSMFH0468 OSMFD0468 OSMFE0468 OSMFF0468 OSMFG0468

High-Speed Steel Jewelers Slotting Saws
Designed for cutting thin tubing, thin walled parts, and extrusions where minimum tooth engagement in the material is of special concern.


•Ground Teeth
•M-2 High Speed Steel
•Hollow Ground For Side Clearance
•Rake Angle of Teeth:  0°
•Metric Sizes Available
 

RESHARPENING SERVICE
Complete resharpening
    service is available.
Pices on Application

COATING SERVICE
TiN, TiCN and other surface
   coatings are available.   Prices on application
Tolerances: O.D. ± .005;
Thickness + .001  - .000
Closer tolerances available,
at additional cost.

(ADD NO. OF TEETH TO THE
CATALOG NUMBER WHEN ORDERING)
(3" & 4" O.D.'s WITH 1/2" HOLES,
ADD "*" AFTER THE PART NO.)

STOCK SAWS

Thickness

 O.D. 1-3/4" 2" 2-1/2" 3" 4"
B&S Gage No. and Fraction

Decimal		 Hole 1/2" 1/2" 1/2" 1/2" *, 1" 1/2" *, 1"
No.of Teeth
132, 160
110, 152
140, 190
170, 224
224, 300
15 0.057"   OJA057 OJJ057 OJH057 OJD057(*) OJE057(*)
16 0.051"   OJA051 OJJ051 OJH051 OJD051(*) OJE051(*)
3/64" 0.047"   OJA047 OJJ047 OJH047 OJD047(*) 0JE047(*)
17 0.045"   OJA045 OJJ045 OJH045 OJD045(*) OJE045(*)
18 0.040"   OJA040 OJJ040 OJH040 OJD040(*) OJE040(*)
19 0.036"   OJA036 OJJ036 OJH036 OJD036(*) OJE036(*)
20 0.032"   OJA032 OJJ032 OJH032 OJD032(*) OJE032(*)
21 0.028"   OJA028 OJJ028 OJH028 OJD028(*) OJE028(*)
22 0.025"   OJA025 OJJ025 OJH025 OJD025(*) OJE025(*)
23 0.023"   OJA023 OJJ023 OJH023 OJD023(*) OJE023(*)
24 0.020"   OJA020 OJJ020 OJH020 OJD020(*) OJE020(*)
25 0.018"   OJA018 OJJ018 OJH018 OJD018(*) OJE018(*)
26 0.016"   OJA016 OJJ016 OJH016 OJD016(*) OJE016(*)
27 0.014"   OJA014 OJJ014 OJH014 OJD014(*) OJE014(*)
28 0.012"   OJA012 OJJ012 OJH012 OJD012(*) OJE012(*)
30 0.010"   OJA010 OJJ010 OJH010 OJD010(*) OJE010(*)
32 0.008"   OJA008 OJJ008 OJH008 - -

CARBIDE METAL-WORKING SAWS

     While High-Speed Steel Saws handle  most slotting tasks, Tungsten-Carbide Saws have steadily gained in popularity for many applications, especially where shock-loading does not appear to be a factor.
     Carbide, while harder than steel, is brittle and should not be subjected to applications where shock may shorten the service life of the tool.
     SPECIALS:  An almost endless number of variations from the tooth types and specifications shown below can be furnished to suit your exact needs and at comparable prices.  Let us know your particular requirements so we can quote price and delivery.
     Specify thickness and number of teeth when ordering.

C-2 Carbide

Hollow Ground For Side Clearance

Rake Angle of Teeth: 5 Degrees Positive

Metric Sizes Available
Tolerances:

O.D. ±.005; Thickness ± .005;
I.D. +.001 -.000 Closer tolerances available at additional cast.
Thickness
Range		 O.D. 1-1/2" 1-3/4" 1-3/4" 2" 2" 2-1/4" 2-1/4" 2-1/2" 2-3/4" 3" 4" 5" 6"
Hole 1/2" 1/2" 7/8" 1/2" 1" 5/8" 1" 1" 1" 1" 1" 1" 1"
No. of
Teeth		 36 38 38 40 40 44 44 48 60 72 80 100 120
.010"-.019"   X1I X1A X1AA X1J X1JJ X1B X1BB X1H X1C X1D - - -
.020"-.030"   X2I X2A X2AA X2J X2JJ X2B X2BB X2H X2C X2D X2E - -
.031"-.050"   X3I X3A X3AA X3J X3JJ X3B X3BB X3H X3C X3D X3E X3F X3G
.051"-.070"   X4I X4A X4AA X4J X4JJ X4B X4BB X4H X4C X4D X4E X4F X4G
.071"-.090"   X5I X5A X5AA X5J X5JJ X5B X5BB X5H X5C X5D X5E X5F X5G
.091"-.110"   X6I X6A X6AA X6J X6JJ X6B X6BB X6H X6C X6D X6E X6F X6G
.111"-.130"   X7I X7A X7AA X7J X7JJ X7B X7BB X7H X7C X7D X7E X7F X7G
.131"-.150"   X8I X8A X8AA X8J X8JJ X8B X8BB X8H X8C X8D X8E X8F X8G
.151"-.170"   X9I X9A X9AA X9J X9JJ X9B X9BB X9H X9C X9D X9E X9F X9G
.171"-.190"   X10I X10A X10AA X10J X10JJ X10B X10BB X10H X10C X10D X10E X10F X10G
.191"-.210"   X11I X11A X11AA X11J X11JJ X11B X11BB X11H X11C X11D X11E X11F X11G
.211"-.230"   X12I X12A X12AA X12J X12JJ X12B X12BB X12H X12C X12D X12E X12F X12G
.231"-.250"   X13I X13A X13AA X13J X13JJ X13B X13BB X13H X13C X13D X13E X13F X13G
Specify Thickness and Number of Teeth When Ordering.

Carbide Cut-Off Saws
(Available in High-Speed Steel, upon Request)
Carbide Cut-Off Saw
 

C-2 Carbide

Hollow Ground
For Side
Clearance

Rake Angle
of Teeth: 5° Pos.

Keyways are
optional at
extra cost

These saws are used for Rotary Cut-Off applications. The saws are made from  C-2 Micro Grain Carbide and are produced to very close tolerances.

Tolerances: O.D. = ±.005 Thickness = ±.0005 I.D. = +.001 -.000 (Closer tolerances available at additional cost.)

RESHARPENING SERVICE
Complete resharpening
service is available.

COATING SERVICE
TiN, TiCN and other surface
coatings are available.

STOCK SAWS
  O.D.

3"

 3-1/2" 4"

Thickness

Hole

1"

1"

1"
No. of Teeth

90, 120

 90, 120

90, 120

.064"

   XSAD064

XSAK064

 XSAE064

.045"

  

XSAD045

XSAK045

 XSAE045

.032"

  

XSAD032

XSAK032

 XSAE032
Home | Metal Working Mica Saws | Rotary Burs | Undercutters | Abrasives | Commutator Grinders | Electrical Test Equipment | Electrician's Hand Tools | Other Products