Electric Motor Repair - About Martindale Electric Co

Española

Français

CLICK HERE for Printable Version of this page.

Cuts either "U" or "V" slots. 1/5 h.p. Universal Motor. Control Switch in Handle. Overall Length 16-1/2". Weighs only 8-1/4 lbs. Used on all sizes of commutators. Well balanced. Easy to Guide.
Model K Mica-Miller	Catalog Number
	115 V.60 Hz.	230 V, 50/60 Hz.
With "Small" Head, 5/16" arbor	M-MU101A	M-MU101B
With "Standard" Head, 5/16" arbor	M-MU102A	M-MU102B
With "Standard", 7mm. arbor	M-MU1027MA	M-MU1027MB
With "Heavy-Duty" Head, 3/8" arbor	M-MU103A	M-MU103B
Extra Interchangeable Heads only:		Catalog Number
"Small", 5/16" arbor		M-MU01
"Standard", 5/16" arbor		M-MU02
"Standard", 7mm. arbor		M-MU027M
"Heavy-Duty", 3/8" arbor		M-MU03
Steel Carrying Case, No.1; for Model K Mica-Miller		CASE101
Net Weight 8 lbs., Shipping Weight 11 lbs. For Saws and Cutters, See Below

Model K Mica-Miller
Powerful, Light-Weight, Easy To Use

The Model K Mica- Miller is an excellent all-around Undercutter for industrial plants or repair shops, as it can be used in the shop or taken to the job, and can be operated on either A.C. or D.C. form any lighting circuit.

     Three interchangeable heads (see below) make the model K most versatile. Saws or "V" cutters from 23/32" to 1-1/4" diameter can be used to undercut commutators of virtually any size.
Full load saw spindle speeds are as follows
    With "Small" Head - 3500r.p.m.
    With "Standard" Head - 2800r.p.m
    With "Heavy-Duty" Head - 1850 r.p.m.
The slot guide provided on the two smaller heads is positioned by two sensitive screw adjustments. It may be swung out of the way when changing saws. Many operators find the model K so easy to use they remove the guide entirely.

Interchangeable Heads for Martindale Mica-Millers

THREE MODELS - MORE VERSATILE
     The three Martindale Mica-Millers are the results of continuous research and "on-the-job" testing in an effort to make the most serviceable all-around portable mica undercutters possible.
Three Models
     This versatile tool is available with three different power sources; Model K (direct drive electric motor), Flex-Drive (flexible shaft), Air-Driven (air motor), to meet the requirements and preferences of all electric repair shops and maintenance departments.
Three Interchangeable Heads
     Also available for use on any of the three models are three interchangeable heads which make it possible to use the Mica-Miller with saws or "V" cutters ranging from 23/32" diameter to 1-1/4" diameter to undercut a wide range of commutator sizes. All three heads are equipped with depth gauges. The two smaller ones have slot guides and the Heavy-Duty head has roller supports. Standard and Heavy-Duty heads have ball bearing spindles.
The "Small" head allows undercutting closer to risers than has been possible before. The "Standard" head is for all-around use, while the "Heavy-Duty" head, with its larger and more rugged parts, will withstand hard usage on larger commutators. To change from one size head to another it is necessary only to remove one screw, change heads and replace screw.

Three Interchangeable Heads
	"SMALL" HEAD (Left) only 1-7/8" wide (less Slot-Guide). Uses 23/32" or 3/4" diameter × 5/16" hole Saws or "V" cutters.
		"STANDARD" HEAD (Above) 2-1/4" wide (less Slot-Guide). Available for use with 7/8" or 1" diameter × 5/16" hole, or 25 mm. diameter × 7mm. hole Saws or "V" cutters.
		"Heavy-Duty" Head (Left) 4/1/4" wide overall. Uses 1-1/8" or 1-1/4" diameter × 3/8" hole Saws or "V" cutters.
All Mica-Millers are light-weight, sturdy, and carefully balanced. These qualities give the operator immediate confidence in the tool and his ability to undercut rapidly without fatigue. When Undercutting, start at the riser end of the commutator and pull the tool towards you.

Saws and Cutters for Martindale Mica-Millers
(High-Speed Steel)

Type Number		O.D.	Hole	Catalog Number
For "Small" Head	14-HS Saws	23/32"	5/16"	HSMS14
	15-VHS Cutters	23/32"	5/16"	HSMSV15
	65-HS Saws	3/4"	5/16"	HSMS65
	65-VHS Cutters	3/4"	5/16"	HSMSV65
For "Standard" Head	75-HS Saws	7/8"	5/16"	HSMS75
	75-VHS Cutters	7/8"	5/16"	HSMSV75
	85-HS Saws	1"	5/16"	HSMS85
	85-VHS Cutters	1"	5/16"	HSMSV85
	25-HS Saws	25 mm.	7 mm.	HSMM25
	25-VHS Cutters	25 mm.	7 mm.	HSMMV25
For "Heavy-Duty" Head	96-HS Saws	1-1/8"	3/8"	HSMS96
	96-VHS Cutters	1-1/8"	3/8"	HSMSV96
	106-HS Saws	1-1/4"	3/8"	HSMS106
	106-VHS Cutters	1-1/4"	3/8"	HSMSV106

     The table at right lists at least 2 diameters of saws and cutters for each of the three interchangeable M-ca-Miller heads.
     Saws ("U" slot) are stocked in the following thicknesses (thousandths of an inch): 15, 18, 20, 23, 25, 26, 28, 30, 32, 35, 38, 40, 43, 45,50, 53, 55, 58, 60, 63, and 65, and can be supplied in other thicknesses at a slight additional charge. ( Standard metric thicknesses available.)
     V-cutters ("V" slot) are all .045" thick and are stocked with 40°, 50°, and 60°, angles between cutting edges. 40°, cutters are generally used for thin mica, 50° for medium mica, and 60° for thick mica.

Steel Carrying Cases
Heavy gauge steel carrying cases to protect your Model K, Air-Driven or Flex-Drive Mica-Miller, extra heads, saws and cutters, accessories, etc., are available.